服務熱線電話
400-6188-756
超聲波清洗機使用注意事項
來源:http://m.ufanr.com.cn/ 時間: 2022-08-12 瀏覽次數: 0
另一方面可以避免安全事故。
On the other hand, safety accidents can be avoided.
一、超聲波清洗機使用注意事項
1、 Precautions for use of ultrasonic cleaning machine
1、清洗機應放置在清潔、干燥以及無強腐蝕氣體和環境中使用,并避免劇烈震動。
1. The cleaning machine should be placed in a clean, dry environment without strong corrosive gas and avoid violent vibration.
2、發生器背面應留有足夠的散熱空間。
2. Sufficient heat dissipation space shall be reserved at the back of the generator.
3、確保機器有良好的接地,以避免人身傷害事故。
3. Ensure that the machine is well grounded to avoid personal injury.
4、清洗機工作時,不要將手指浸入清洗液中。
4. Do not immerse your fingers in the cleaning liquid when the cleaning machine is working.
5、嚴禁空載狀態下開機,開機前按使用說明的液位將清洗液倒入清洗槽內。
5. It is forbidden to start the machine under no-load condition. Before starting the machine, pour the cleaning liquid into the cleaning tank according to the liquid level specified in the instructions.


6、被清洗物不得和槽底接觸,建議將工件放入籃筐中清洗。
6. The object to be cleaned shall not contact with the bottom of the tank. It is recommended to put the workpiece into the basket for cleaning.
7、清洗液不得呈強酸或強堿性,在沒有可靠的安全措施條件下,不能使用易燃溶液。
7. The cleaning solution shall not be strong acid or strong alkaline. Flammable solution shall not be used without reliable safety measures.
8、清洗液溫度會隨連續工作時間而升高,清洗機連續工作時間建議不要超過8小時。
8. The temperature of the cleaning liquid will rise with the continuous working time. It is recommended that the continuous working time of the cleaning machine should not exceed 8 hours.
9、如發現清洗槽有漏水現象,應立即關機停用,并倒空清洗液后與銷售商聯系。
9. In case of water leakage in the cleaning tank, shut down the machine immediately and contact the seller after emptying the cleaning solution.
10、不允許擅自拆開機器。
10. Do not disassemble the machine without permission.
11、對有加熱裝置的清洗機在清洗完畢后,先關閉加熱器待清洗液冷卻后再放空清 洗液。
11. For the cleaning machine with heating device, after cleaning, turn off the heater first and then vent the cleaning liquid after the cleaning liquid is cooled.
二、超聲波清洗機正常工作步驟
2、 Normal working steps of ultrasonic cleaning machine
1、檢查電源是否正常,開關是否正常,指示燈、指示表是否正常,保證清洗槽干凈。
1. Check whether the power supply is normal, whether the switch is normal, whether the indicator light and indicator meter are normal, and ensure that the cleaning tank is clean.
2、放入清洗液,方可打開工作電源,觀察電流指示表的讀數是否在80-100之間,清洗液溫度在40-60℃之間,同時水槽會出現微小氣泡并伴隨有“吱,吱”的聲響,這就表示開始正常清洗。
2. After the cleaning liquid is put in, the working power can be turned on. Observe whether the reading of the current indicator is between 80-100 ° C and the temperature of the cleaning liquid is between 40-60 ° C. at the same time, small bubbles will appear in the water tank with the sound of "squeak, squeak", which means that the normal cleaning is started.
3、在超聲波清洗過程中戴上絕緣手套。
3. Wear insulating gloves during ultrasonic cleaning.
4、清洗物件不能直接放置在缸底,以免影響清洗效果,應放在專用清洗籃內或采用零裝方法。
4. The cleaning objects shall not be directly placed at the bottom of the cylinder to avoid affecting the cleaning effect. Instead, they shall be placed in the special cleaning basket or the zero packing method shall be adopted.
5、缸內無清洗液時切勿開機,以免損壞換能器。
5. Do not start the machine when there is no cleaning fluid in the cylinder to avoid damaging the transducer.
6、長期不使用時,機器應保存在干燥處。
6. When not used for a long time, the machine should be stored in a dry place.
7、把工件料盤放入超聲波清洗槽中,進行液體清洗。
7. Put the workpiece tray into the ultrasonic cleaning tank for liquid cleaning.
8、工作時間按工件需求去設置。
8. The working time is set according to the requirements of the workpiece.
9、防止工件在清洗過程中劃傷表面及丟失,保證工件數量的完整。
9. Prevent the workpiece from scratching the surface and losing during cleaning, and ensure the integrity of the number of workpieces.
10、清洗完成后,切斷工作電源,防止事故的發生。
10. After cleaning, cut off the power supply to prevent accidents.
11、取出工件料盤,做好下道工序的工作。
11. Take out the workpiece tray and do a good job in the next process.
以上就是為大家介紹的有關超聲波清洗機價格的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.ufanr.com.cn
The above is the detailed introduction about the price of ultrasonic cleaning machine. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://m.ufanr.com.cn
相關文章
-
全自動多槽超聲波清洗機工作原理是怎樣的?工業用高壓清洗設備 清洗大型工業設備 2025-11-24
-
單工位旋轉噴淋清洗機在使用的注意要點 2025-11-23
-
淺述全自動超聲波清洗機四種不同過濾類型的各自特點 2025-11-22
-
全自動多槽超聲波清洗機的常見故障解決方法分享 2025-11-21
-
還不會使用多槽式超聲波清洗機?進來看 2025-11-20
-
高壓去毛刺清洗機,讓工件上的毛刺無所遁形 2025-11-19
-
CNC高壓清洗機助力精密零件高效清洗 2025-11-18
-
通過式噴淋清洗機的原理是什么? 2025-11-17
-
噴淋清洗機與傳統清洗方式相比,到底有何優勢? 2025-11-15
-
這些關鍵因素在選擇多槽手動超聲波清洗機時要多加考慮 2025-11-14

新聞中心




行業新聞







魯公網安備37011202000628號